FRP #32 - Let's go back to the start...

Do you have a Puma that is a project? Do you want to track the progress with your own thread? Feel free to do it here.

Moderator: Moderators

User avatar
xnbradley
Adolescent
Adolescent
Posts: 120
Joined: Mon Oct 10, 2016 3:24 pm
Model: FRP
Location: Odiham, Hampshire

FRP #32 - Let's go back to the start...

Postby xnbradley » Mon Dec 12, 2016 9:37 pm

What is this...

jacko wrote:Source of the post JANSPEED; RACING PUMA OWNERS CLUB. you have to be a member to buy these but they are not asking for membership numbers to prove this. they have used the original jigs to make these and also using a janspeed stainless backbox. added bonus is that it comes with the original tailpipe.


Are these still available?

Thanks
0 x

User avatar
xnbradley
Adolescent
Adolescent
Posts: 120
Joined: Mon Oct 10, 2016 3:24 pm
Model: FRP
Location: Odiham, Hampshire

FRP #32 - Let's go back to the start...

Postby xnbradley » Mon Dec 12, 2016 10:10 pm

Just found the receipt from 2012...

currently have a Piper CAT on the car from Pumabuild...

What to do...
0 x

User avatar
XAF
Project Petrol Head!
Project Petrol Head!
Posts: 703
Joined: Sun Apr 08, 2012 6:33 pm
Model: 1.7

FRP #32 - Let's go back to the start...

Postby XAF » Tue Dec 13, 2016 12:10 am

Are you sure it's the cat, not a lambda, dirty air filter, plugs, leads, coil pack, MAF etc?

The FRP cats are very sensitive to proper emissions control. One part slightly out (like the tiny wire in the MAF) could be enough to foul the readings.

I've got a Piper cat and it's well within emissions, even when not toasty hot.
0 x
2000 Puma Lux
2000 FRP #477

User avatar
xnbradley
Adolescent
Adolescent
Posts: 120
Joined: Mon Oct 10, 2016 3:24 pm
Model: FRP
Location: Odiham, Hampshire

FRP #32 - Let's go back to the start...

Postby xnbradley » Tue Dec 13, 2016 12:18 am

to be honest... i haven't got a clue...

I sprayed the MAF with Carb cleaner the other day... air filter looked pretty clean... no idea how to test the lambda leads... can you do that with ForScan?

I will chat though the above with the mechanic tomorrow...

Just trying to source the Goodridge hose and adapters so I can at least get it back home...

not a good day...
0 x

User avatar
Wild E. Coyote
Guru!
Guru!
Posts: 1907
Joined: Wed Apr 13, 2011 9:47 am
Model: 1.7
Location: Croatia

FRP #32 - Let's go back to the start...

Postby Wild E. Coyote » Tue Dec 13, 2016 7:46 am

If you sprayed MAF with carb cleaner it is not working as it should. Carb cleaner leaves an oily surface for lubrication purposes (as carb has moving parts). After carb cleaner apply some brake cleaner to degrease it properly.
How is your idle? When cleaned with brake cleaner it should be rock steady and engine should get more responsive
0 x

User avatar
xnbradley
Adolescent
Adolescent
Posts: 120
Joined: Mon Oct 10, 2016 3:24 pm
Model: FRP
Location: Odiham, Hampshire

FRP #32 - Let's go back to the start...

Postby xnbradley » Wed Dec 14, 2016 1:02 am

So...

today I have ordered a stainless Steel mid section from Chris and a couple of hose fittings to fix the PAS hose...

heart breaking stuff owning a FRP... I just want to get her back on the road...

oh well...
0 x

User avatar
tuonokid
Project Elder
Project Elder
Posts: 3105
Joined: Fri Nov 23, 2012 8:41 pm
Model: 1.7
Location: Huddersfield

FRP #32 - Let's go back to the start...

Postby tuonokid » Wed Dec 14, 2016 1:11 am

Hi Christian
You'll get there in the end :-)
Barry
0 x
2001 ColOrado red Puma 1.7, work in progress.
Westfield SEIW 1800 Zetec.
Building Westfield SEI 2.0 Zetec Blacktop on TBs.
Fiesta Style 1.25
Aprilia Tuono Factory.
1975 Yamaha TY80
Now working on my sons Anglia 105e

My Project Link - viewtopic.php?f=64&t=23509

gingerdave
Project Petrol Head!
Project Petrol Head!
Posts: 569
Joined: Tue Feb 12, 2013 9:00 am
Model: Millennium
Location: essex boy ...in worcestershire

FRP #32 - Let's go back to the start...

Postby gingerdave » Wed Dec 14, 2016 2:46 pm

xnbradley wrote:Source of the post So...

today I have ordered a stainless Steel mid section from Chris and a couple of hose fittings to fix the PAS hose...

heart breaking stuff owning a FRP... I just want to get her back on the road...

oh well...

Heart breaking?...sounds more like bank breaking.NEVER LET IT BEAT YOU!!!
1 x
Puma millennium x2
2.3 diesel Sierra
Bemani Exige
Escort mk2
S1 FHC E Type
Ford Ka
Escort mk 1
Shagged out Peugeot 405
Citroen BX which is busted
Kawasaki Z1000J

And a Grey Fergie

DOH
Project Regular
Project Regular
Posts: 278
Joined: Sat Dec 11, 2010 6:13 pm
Model: 1.7
Location: UK

FRP #32 - Let's go back to the start...

Postby DOH » Thu Dec 15, 2016 11:09 pm

Re :High CO readings for MOT
Things to try are as follows:

1) have you ensured that the airfilter is clean?
2) Search for info I posted about testing the lambda sensor resistance readings of 13 ohms, If the pre heater is open circuit. (IIrc 2 the grey wires? , verified by carrying out an ohms test ,)then your idle readings & idle will be affected.http://www.projectpuma.com/viewtopic.php?f=25&t=17895&p=229512&hilit=lambda+sensor+ohms#p229512
3) Remove and clean Lambda sensor with Carb Cleaner
4) Clean the injectors, they maybe gummed up and not closing off fully and therefore weeping fuel into the engine, which can also result in high CO readings
0 x

User avatar
xnbradley
Adolescent
Adolescent
Posts: 120
Joined: Mon Oct 10, 2016 3:24 pm
Model: FRP
Location: Odiham, Hampshire

FRP #32 - Let's go back to the start...

Postby xnbradley » Fri Dec 16, 2016 8:14 pm

So...

From the M to the O to the T... #032 is finally free...

New stainless steel mid section fitted... passed emissions with flying colours...

Fast Idle CO Max 0.20% - passed at 0.01%
Natural Idle CO Max 0.30% - passed T 0.05%

and this was when the engine was not hot at all...

Thanks to Chris for sorting the CAT out for me...

One of the best journeys so far... so glad I have another 12 months to restore the car to its former glory...

gonna take a rest over Christmas and will start again in the new year... maybe I need to make a list and come up with a schedule of what and when to do things...

may go for a drive tomorrow... for no apparent reason...

be good...
3 x

User avatar
tuonokid
Project Elder
Project Elder
Posts: 3105
Joined: Fri Nov 23, 2012 8:41 pm
Model: 1.7
Location: Huddersfield

FRP #32 - Let's go back to the start...

Postby tuonokid » Fri Dec 16, 2016 8:30 pm

Well done Christian. If there's no history of the cambelt being changed get it shipped off to Chris ASAP.
Barry
0 x
2001 ColOrado red Puma 1.7, work in progress.
Westfield SEIW 1800 Zetec.
Building Westfield SEI 2.0 Zetec Blacktop on TBs.
Fiesta Style 1.25
Aprilia Tuono Factory.
1975 Yamaha TY80
Now working on my sons Anglia 105e

My Project Link - viewtopic.php?f=64&t=23509

gingerdave
Project Petrol Head!
Project Petrol Head!
Posts: 569
Joined: Tue Feb 12, 2013 9:00 am
Model: Millennium
Location: essex boy ...in worcestershire

FRP #32 - Let's go back to the start...

Postby gingerdave » Fri Dec 16, 2016 11:04 pm

:grin:
0 x
Puma millennium x2
2.3 diesel Sierra
Bemani Exige
Escort mk2
S1 FHC E Type
Ford Ka
Escort mk 1
Shagged out Peugeot 405
Citroen BX which is busted
Kawasaki Z1000J

And a Grey Fergie

User avatar
red
Site Administrator
Site Administrator
Posts: 10150
Joined: Wed Oct 03, 2007 4:31 pm
Model: Other
Location: Cambridgeshire
Contact:

FRP #32 - Let's go back to the start...

Postby red » Fri Dec 16, 2016 11:38 pm

:ok: congratulations on getting it through and good luck concocting "the list!"
0 x
FRP#0201 (2000) 2009-2011
Melina Blue (1999) 2006-2009
Moondust Silver (2000) 2006

User avatar
XAF
Project Petrol Head!
Project Petrol Head!
Posts: 703
Joined: Sun Apr 08, 2012 6:33 pm
Model: 1.7

FRP #32 - Let's go back to the start...

Postby XAF » Fri Dec 16, 2016 11:45 pm

Good news Christian! Go enjoy and make your mind up in the new year what you're gonna do
0 x
2000 Puma Lux
2000 FRP #477

User avatar
Wild E. Coyote
Guru!
Guru!
Posts: 1907
Joined: Wed Apr 13, 2011 9:47 am
Model: 1.7
Location: Croatia

FRP #32 - Let's go back to the start...

Postby Wild E. Coyote » Sat Dec 17, 2016 8:37 am

Glad it is ok. Regarding the suggestion above: repair everything that needs be done, of course!
0 x

User avatar
xnbradley
Adolescent
Adolescent
Posts: 120
Joined: Mon Oct 10, 2016 3:24 pm
Model: FRP
Location: Odiham, Hampshire

FRP #32 - Let's go back to the start...

Postby xnbradley » Sat Dec 17, 2016 9:43 am

Thanks guys...

The cam belt has definitely been changed in the last five years... just waiting to hear back on the exact date... should be ok until the spring/summer when I'm gonna get Chris to strip and service the engine...

hopefully I will have removed quite a bit from my donour car... stripped... serviced... cleaned and sealed ready to fit..

I may look at the front bumper repair next... kinda like the idea of getting the Splitter back on... no foubt I will be asking for advice...

peace
0 x

User avatar
red
Site Administrator
Site Administrator
Posts: 10150
Joined: Wed Oct 03, 2007 4:31 pm
Model: Other
Location: Cambridgeshire
Contact:

FRP #32 - Let's go back to the start...

Postby red » Sat Dec 17, 2016 11:24 am

An FRP without the splitter fitted just is not right :-)
0 x
FRP#0201 (2000) 2009-2011
Melina Blue (1999) 2006-2009
Moondust Silver (2000) 2006

CeReD
Adolescent
Adolescent
Posts: 64
Joined: Tue Jun 19, 2012 1:23 pm
Model: 1.7

FRP #32 - Let's go back to the start...

Postby CeReD » Fri Jan 06, 2017 12:45 am

I'm still looking to buy, will be happy to put her right!

Glad it's now playing ball for you now though, defo get a splitter put on
0 x


Return to “ProjectPuma”

Who is online

Users browsing this forum: No registered users and 3 guests